Expert Answers about Chevrolet P Series

Trailer Hitch Receiver For a 1985 Itasca Sunflyer On Chevy P30 Chassis
I recommend looking at the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. This is a universal receiver you can use as there currently is not a custom fit receiver for your 1985 Itasca Sunflyer on a Chevrolet P30 chassis. This particular receiver can be welded or bolted to the frame and uses 7" tall brackets. We do have the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 that uses 16" long brackets depending on the amount of drop you need on the...
view full answer...

Correct Replacement Convertor for Magnatek 6345
I have another option but I spoke to my contact at Progressive Dynamics and he said the Lithium Converter for WFCO RV Power Centers - 35 Amp # PD4635LIV will not be a replacement for the Magnatek 6345 because it needs to come in its own steel box. He said that the correct replacement for the Magnatek 6345 will be the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp # PD4645V. He told me that the # PD4645V comes with a switch that allows you to charge lithium...
view full answer...

Trim Kit Mounting Hole Spacing for Greystone Built-in Microwave
The Greystone Built-in Microwave # 324-000106 measures 19" wide so it will fit that part of your cutout, but you also need to make sure that it can accommodate the 14" depth and 13-1/4" height of this microwave as well. The included trim kit measures 23-3/8" wide x 15" tall x 13-1/2" deep with the mounting holes being 22-1/4" left to right and 12-1/4" top to bottom. I have attached a review video and some photos with dimensions that you can check out. I'm not sure if this will last an...
view full answer...

Will Air Lift Compressor Kit AL25856 Work on 1994 Fleetwood Flair RV
Yes, as long as your RV has a 12 volt electrical system (it does), the Air Lift Compressor System part # AL25856 will fit and work well.
view full answer...

Are The Buyers Products Mud Flaps 337B36LP Sold As A Pair
The Buyers Products Mud Flaps - Black Rubber - 24" Wide x 36" Tall x 1/4" Thick # 337B36LP you were looking at come as a pair. You may also be interested in the Buyers Products Anti-Sail Brackets for Mud Flaps # 337405BC which can be used to mount the mud flaps to your 1993 Chevrolet P Series Motorhome. These also come as a pair. I included videos for all of the products mentioned for you to take a look at.
view full answer...

Will the Air Helper Springs for Coil Springs Part # AL81560 Fit a 1985 Sport Coach Pathfinder
Yes, the Air Lift AirLift 1000 Air Helper Springs for Coil Springs part # AL81560 is a confirmed fit for your 1985 Sport Coach Pathfinder which is on a Chevrolet P Series chassis. The shipping cost will be displayed upon checkout.
view full answer...

Hauling a Front Mounted Generator Options
In order to haul a generator on the front of your vehicle, I suggest using a front mount trailer hitch such as the # 13703. This is an adjustable type hitch that fits frames from 22" to 72" in width. It is not a custom fit but will require a little bit of fabrication and some welding. Curt states that all non-trailered loads need to be secured with Stabilizing Support Strap # 18050. After installation of adjustable hitch, you can use a cargo basket carrier such as the Curt Cargo Carrier...
view full answer...

What Are The Best Stabilizer Options For A 1994 Chevrolet P-30 Series
You are correct, the 1994 Chevrolet P-Series Chassis came with both two wheel drive front coil spring suspension and four wheel drive front leaf spring suspension setups. Fortunately, we have stabilizer and sway control options for both models. For your coil spring suspension, I recommend using both a front steering stabilizer and rear axle stabilizer. For the front steering stabilizer, I recommend using the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Motor Homes...
view full answer...

Replacement 26 Inch Wiper Blades for 1992 Fleetwood Bounder Class A Motorhome
The ClearPlus 77 Series HD Windshield Wiper Blade - 26 inch # CP77261 will work on your 1992 Fleetwood Bounder Class A Motorhome. The wide saddle mount is the design that installs by using two screws. This wiper blade offers both the connectors for installation to the 1/2 inch to 5/8 inch wide saddle mount and the 12 x 4 J-hook. This part number is for a quantity of one wiper blade
view full answer...

Where Does the Bare Copper Wire Go on the Furrion Chill HE RV Air Conditioner System
The bare copper wire with clear tube on the control box of the distribution for the Furrion Chill HE RV Air Conditioner System part # FR92PR is an air temp sensor. It needs to be pointed straight up toward the overhead unit. It does not correct directly to any other wires or devices.
view full answer...

Recommended Anti-Sway Bar For A 1995 Georgie Boy P-Series Chassis
No, the Roadmaster Rear Anti-Sway Bar # RM-1259-109 is not a confirmed fit for your P-Series Chassis. The only anti-sway bar that we carry for a P-Series Chassis like your 1995 Georgie Boy would be the Roadmaster Front Anti-Sway Bar and Bushing Kit # RM-1109-116.
view full answer...

RV City Water Inlets for 1997 Dolphin Motorhome
We have great options for RV city water inlets like the part # 372160-85-A-3PA for a black inlet or part # 37262145 for white.
view full answer...

2505-8305 Model Steps on a 1990 Airstream 345 Motor Home Will Not Fully Extend
The motor is likely the culprit of your steps not retracting all the way. The nylon gear inside the motor is likely the part that is worn. The step is able to extend due to gravity but it sound like the motor does not have enough power on the upstroke to fully retract. Unfortunately, I am not able to reference the model number that you provided. However, if it is a Kwikee Step then there would not be any replacement parts for you due to the age of the step. Therefore, your only option would...
view full answer...

Install Photo of Timbren Front Suspension Enhancement System TGMFP30W
I have attached for you below a photo from the instructions of the Timbren Front Suspension Enhancement System part # TGMFP30W. I have also attached for you below the install instructions so you can see the whole process yourself. Unfortunately, we do not have any install videos at this time.
view full answer...

Dimensions of Air Bag of Air Lift Kit AL88203
Just the air bag of the Air Lift kit part # AL88203 measures 7 inches by 7 inches. It's wider than the brackets it mounts on so the bracket width wouldn't affect compatibility of your application.
view full answer...

Are Air Springs Available Separately For Firestone Coil-Rite F4100
Yes, individual air springs are available for the W237604100, which are Coil-Rite springs, which you can find at the following part number: - Firestone Coil-Rite Air Helper Springs - Front Axle # F4100 The replacement, individual air springs for the # F4100 are the Replacement Air Spring for Firestone Coil-Rite Front-Axle Kit 4100 # F6000. This is the correct part, and the exact same thing as the 6100 you mentioned, just a different part number.
view full answer...

Solution for Needing Replacement Kwikee 9513 Replacement Module
We do have a solution though there isn't an exact replacement module for a 9513 unit manufactured before 1999. Instead, what you'll need to do is upgrade your steps with the Motor Upgrade Kit for Kwikee Electric RV Steps # LC379145. This will give you a new - and better performing - motor, linkage, control unit, switch kit, and hardware. I have added links to a couple video reviews I recommend checking out as well.
view full answer...

Possible Hitch to Fit 1995 Chevrolet P30
Your 1995 Chevrolet P30 is the type of vehicle that the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 was intended for. This is a multi-fit hitch that comes with brackets that allow it to drop down 16 inches to clear the lower bumper of your van. As long as your frame is less than 44 inches wide this hitch could be made to fit since it's a universal design. We have a version of this with shorter drop brackets as part # 41990-07 which has 7 inches of drop instead.
view full answer...

Dimensions for Buyers Product Wiring Junction Box # 3375601101
The Buyers Products Trailer Wiring Junction Box # 3375601101 referenced in your question measures 6.5 inches long, 3.21 inches wide, and 2.5 inches tall when the cover is installed. The mounting holes at each end are spaced apart 7.38 inches on center. I have attached an image to assist.
view full answer...